How To Use A Bead Crimper?

Rate this post

Crimp beads are used to assist fasten a loop on a piece of jewelry, which enables the completed item to be linked to further parts of jewelry. If you are going to build your own beaded jewelry, you will most likely need to crimp the wire on both ends in order to prevent the beads from falling off of the wire. How To Use A Bead Crimper?

It is recommended that you purchase a set of crimping pliers to get the greatest results; however, an ordinary pair of pliers may also be used successfully. In order to utilize crimp beads, first thread on the crimp beads, then shape the bead, and then finish the procedure by fastening the ornamental beads with an additional crimp bead.

The Initial Step: Stringing the Crimp Bead

Collect all of your supplies. Determine the size of the wire you have available first. Make sure you have the appropriate size crimp beads for your wire by consulting a chart that you may get online. Because the number of strands of wire or thread that you will be crimping at simultaneously will determine the size of the bead that you will need, it is important to take this into mind.

For instance, if you are working with a single length of wire that measures 0.020 inches (0.51 millimeters), you will require a bead that has a diameter of 0.040 inches (1.02 mm). However, if you are working with two strands of wire, you will want beads that have a diameter of 0.080 inches.

To complete your wire, add an end piece. You will need some kind of end piece, like a clasp, to attach one end of the wire so that your beads do not come loose while you are wearing the necklace. When you are ready to connect a clasp, you should begin by passing the end of your beading wire (jewelry cable) through a crimp bead. Next, you should pass the wire through the eye of the clasp.
It’s possible that your design may need other sorts of end components, including a closed or solid jump ring or an extension chain. These may be attached using the same ways as are used for clasps.

Create a closed loop. Create the loop by threading the crimp bead and clasp together. After you have threaded the crimp and the clasp, you will need to construct a loop by feeding the wire back through the crimp bead. It is recommended that you leave a tail of wire that is a couple of inches longer than you believe you will need in order to ensure that you have enough wire to work with.

  How To Find Points Of Discontinuity?
How To Use A Bead Crimper? Source: Youtube

Crimp Beads, Part 2: Forming the Beads

Move the crimp bead down the wire with your finger. Bring the crimp bead as near as possible to the end of the end piece or clasp. Check the crimp bead to see whether it is too near to the clasp or the end piece, and if it is, move it farther away. You want to have a little loop around the clasp or the end piece, but you don’t want it to be so small that it locks the clasp in place so firmly that it can’t move freely.

Make the bead more flat. To flatten the bead, crimping pliers should be used. Put pressure on the beads using the channel on the rear of the crimping pliers that is flat and is located closest to the handle. Close the pliers by applying a little, yet strong, amount of pressure. The crimp bead will take on the appearance of the letter “C” as a result of this action, since it will both flatten out and have a dent placed in the centre of it.

Turn the bead over. Use crimping pliers to give it a round shape. Put the dented crimp bead into the front channel of the crimping pliers, which is the one that is rounded and closest to the tip. When the pliers are closed and squeezed, the bead will be folded closed directly on the dent if you have positioned the “C” such that its upright position faces upward (closing the “C” into an “O”). Apply a little, but firm, pressure to the crimp bead until it has completely closed and is securely wrapped around the wire.
Make sure the wire doesn’t come loose by giving it a little tug. If required, pliers may be used to make the closure more secure.

Use pliers with a chain nose or needle nose. You can get away with using a standard set of pliers if you don’t have access to crimping pliers. They are capable of completing the task at hand, but unlike crimping pliers, the crimps they produce are not perfectly round or uniform. To use these pliers, just grab the crimp bead with the flat portion of the pliers and push gently but firmly to flatten the crimp bead onto the wire. This will allow you to utilize the pliers effectively.
Always use flat pliers or the piece of the pliers that is flat. Additionally, grooves will be left on the surface of the crimp bead while using these pliers since they have teeth.

  How To Clean Homedics Humidifier?

Beading, Part 3: Bringing It All Together

Bead your string with the ornamental beads. Make use of the beads that correspond with the design that you have chosen for your bracelet, necklace, or other item of jewelry. Begin by stringing the first bead onto the wire. The remaining tail of wire should be threaded through the hole in the bead. Make a clean cut on the loose end of the cable by using your flush cutters to get as near as feasible to the bead. Continue to string the remaining beads onto your thread in accordance with your pattern until you reach the other end.

Pull your beads closer together. When you are ready to connect your last clasp to the end of your piece, thread the crimp bead and clasp exactly like you did previously. However, at this point, you will want to tighten all of your beads by pushing on the tail end of the loose wire. This will allow you to attach your final clasp. This will ensure that there are no gaps in your pattern caused by the beads not being tightly packed together.
If your design incorporates long tube beads, you will need to make sure that there is a space between each of the beads that is around the length of your fingernail.
If you want to build a bracelet, you have to check that the length of the wire and the beads is equal to the little circle that goes around a person’s wrist.
Use your pliers if you find that you need more leverage to draw the wire tight; use one to hold the clasp while you use the other to grip the wire and tighten it.

Include a crimp cover for an extra bit of class. You may get crimp covers in the event that you want to conceal your crimp beads. A crimp cover is a bigger, round bead that has the appearance of a crimp bead and is used to cover the crimp bead or tube to give it a more polished appearance. To add a crimp cover, just slip it over the crimp bead and use a pair of pliers to squeeze it tight. This will complete the process.

  How To Clean White Ultra Boost?
How To Use A Bead Crimper?

Do crimp beads function properly when used on thread?

Are thread and crimp beads compatible with one another? It is not suggested to use crimps while creating with thread because the metal edges of a crimp bead might cut or fray the thread when the bead is crimped. Instead, a professional finish may be achieved by tying knots with bead tips or using French wire in your designs.

Why won’t the crimp on my beads stay in place?

Either the diameter of the wire that you used was too little for the project, or you strung your beads in a manner that was too tight. To begin, you need to make certain that the diameter of the wire you are using is big enough to allow it to pass through the beads without causing any discomfort.

Do crimp beads need any specialized pliers to be used?

Crimp beads are soft metal beads that are used as an alternative to knots for the purpose of securing clasps and beads onto stringing materials that cannot be knotted, such as beading wire. In order to work with crimps, you will need either a pair of flat-nosed pliers to compress the crimps into place or a pair of specialized crimping pliers that “fold” the bead into a more compact shape.

What is the key difference between crimp beads and crimp tubes?

Many individuals who work in the jewelry industry choose crimp tubes over crimp beads. The tubes are often more durable and resistant to cracking and breaking compared to the crimp beads. Because tubes often have a greater internal surface area, they may perform a better job of grasping beading wire than other types of containers.

What exactly are the tools used to crimp?

The device that causes the material to be deformed and that is used to produce the connection is called a crimping tool. In the field of electrical work, crimping is a technique that is often used to join individual wires or lines to other connections.

How do I determine the appropriate size crimp bead to use?

In general, a 1mm OD crimp tube of any length is appropriate for use with smaller strands of beading wire (007 to 014), whilst 2mm OD crimps are good for.019 and the 3mm OD crimps are for the heavier strands of beading wire.

Similar Posts